SKF · super precision bearings
SKF S71904/VA9D1
Super-precision angular contact ball bearings — manufacturer technical reference and quotation support in Saudi Arabia.
لطلب عرض سعر في السعودية، أرسل رقم القطعة أو المقاس والكمية والمدينة. يُرجى تأكيد التوافق والتوفر والسعر مع فريقنا.
| Bore diameter | 20 mm |
|---|---|
| Outside diameter | 37 mm |
| Width | 9 mm |
| Contact angle | 25 ° |
| Basic dynamic load rating | 5.72 kN |
| Basic static load rating | 3.05 kN |
| Attainable speed for grease lubrication | 30000 r/min |
| Contact type | Normal contact (two-point contact) |
| Number of rows | 1 |
| Ring type | One-piece inner and outer rings |
| Universal matching bearing | Yes, back-to-back (), face-to-face (>>) |
| Matched arrangement | No |
| Matched condition (axial clearance/ preload) | Not applicable |
| Tolerance class | P4 |
| Material, bearing | Bearing steel |
| Coating | Without |
| Sealing | Seal on both sides |
| Sealing type | Non-contact |
| Lubricant | Grease |
| Special feature | Suitable for driven tools |
| Indicative carbon footprint for new product | 0.14 kg CO_2e |
| Product net weight | 0.037 kg |
| eClass code | 23-05-08-04 |
| UNSPSC code | 31171531 |
| Universal matching bearing(s) | Yes, back-to-back (), face-to-face (>>) |
| Dimensions · Bore diameter · (d) | 20 mm |
| Dimensions · Outside diameter · (D) | 37 mm |
| Dimensions · Width · (B) | 9 mm |
| Dimensions · Shoulder diameter of inner ring (large side face) · (d_1) | 25.6 mm |
| Dimensions · Shoulder diameter of inner ring (small side face) · (d_2) | 25.6 mm |
| Dimensions · Recess diameter of outer ring (large side face) · (D_2) | 34.15 mm |
| Dimensions · Chamfer dimension · (r_1,2) · min. | 0.3 mm |
| Dimensions · Chamfer dimension · (r_3,4) · min. | 0.2 mm |
| Dimensions · Distance from side face to pressure point · (a) | 11.2 mm |
| Abutment dimensions · Diameter of shaft abutment · (d_a) · min. | 22 mm |
| Abutment dimensions · Diameter of shaft abutment · (d_a) · max. | 25.1 mm |
| Abutment dimensions · Diameter of shaft abutment · (d_b) · min. | 22 mm |
| Abutment dimensions · Diameter of shaft abutment · (d_b) · max. | 25.1 mm |
| Abutment dimensions · Diameter of housing abutment · (D_a) · max. | 35 mm |
| Abutment dimensions · Diameter of housing abutment · (D_b) · max. | 35.6 mm |
| Abutment dimensions · Radius of fillet · (r_a) · max. | 0.3 mm |
| Abutment dimensions · Radius of fillet · (r_b) · max. | 0.2 mm |
| Calculation data · Basic dynamic load rating · (C) | 5.72 kN |
| Calculation data · Basic static load rating · (C_0) | 3.05 kN |
| Calculation data · Fatigue load limit · (P_u) | 0.129 kN |
| Calculation data · Attainable speed for grease lubrication | 30000 r/min |
| Calculation data · Contact angle · (α) | 25 ° |
| Calculation data · Ball diameter · (D_w) | 4.762 mm |
| Calculation data · Number of rows · (i) | 1 |
| Calculation data · Number of balls (per bearing) · (z) | 15 |
| Calculation data · Preload and stiffness (back-to-back, face-to-face) · Preload when unmounted · (G) | 70 N |
| Calculation data · Correction factors for preload calculation · Correction factor dependent on bearing series and size · (f) | 1.1 |
| Calculation data · Correction factors for preload calculation · Correction factor dependent on contact angle · (f_1) | 0.98 |
| Calculation data · Correction factors for preload calculation · Correction factor, preload class B · (f_2B) | 1 |
| Calculation data · Factors for equivalent bearing load calculation · Limiting value · (e) | 0.68 |
| Calculation data · Factors for equivalent bearing load calculation · Additional factors for equivalent loads | Refer to Notes 1 and 2 below |
| Calculation data · Factors for equivalent bearing load calculation · Axial load factor (single, tandem) · (Y_1) | 0 |
| Calculation data · Factors for equivalent bearing load calculation · Axial load factor (single, tandem) · (Y_2) | 0.87 |
| Calculation data · Factors for equivalent bearing load calculation · Axial load factor (single, tandem) · (Y_0) | 0.38 |
| Calculation data · Factors for equivalent bearing load calculation · Radial load factor (single, tandem) · (X_1) | 1 |
| Calculation data · Factors for equivalent bearing load calculation · Radial load factor (single, tandem) · (X_2) | 0.41 |
| Calculation data · Factors for equivalent bearing load calculation · Radial load factor (single, tandem) · (X_0) | 0.5 |
| Calculation data · Factors for equivalent bearing load calculation · Axial load factor (back-to-back, face-to-face) · (Y_1) | 0.92 |
| Calculation data · Factors for equivalent bearing load calculation · Axial load factor (back-to-back, face-to-face) · (Y_2) | 1.4 |
| Calculation data · Factors for equivalent bearing load calculation · Axial load factor (back-to-back, face-to-face) · (Y_0) | 0.76 |
| Calculation data · Factors for equivalent bearing load calculation · Radial load factor (back-to-back, face-to-face) · (X_1) | 1 |
| Calculation data · Factors for equivalent bearing load calculation · Radial load factor (back-to-back, face-to-face) · (X_2) | 0.67 |
| Calculation data · Factors for equivalent bearing load calculation · Radial load factor (back-to-back, face-to-face) · (X_0) | 1 |
Family specifications and selection conditions
| Product description | These super-precision, high-capacity, single row angular contact ball bearings with non-contact seals accommodate radial and axial loads acting simultaneously, where the axial load acts in one direction only. Being universally matchable, they can be used together in arrangements to provide effective load sharing, within a predetermined preload range, without the use of shims or similar devices. |
|---|---|
| Manufacturer features | Suitable for driven tools • High axial and radial load carrying capacity • High degree of stiffness • Low noise and vibration levels • Universally matchable • Non-contact seals • Integral sealing prolongs bearing service life |

Manufacturer references
Follow the complete manufacturer documentation for application restrictions, materials, tolerances and installation requirements. Limits may not apply simultaneously. We do not publish inferred stock, pricing or ratings.