SKF · super precision bearings
SKF 71908 FEGA/HCP4AL
Super-precision angular contact ball bearings — manufacturer technical reference and quotation support in Saudi Arabia.
لطلب عرض سعر في السعودية، أرسل رقم القطعة أو المقاس والكمية والمدينة. يُرجى تأكيد التوافق والتوفر والسعر مع فريقنا.
| Bore diameter | 40 mm |
|---|---|
| Outside diameter | 62 mm |
| Width | 12 mm |
| Contact angle | 18 ° |
| Basic dynamic load rating | 10.1 kN |
| Basic static load rating | 6 kN |
| Note | Refer to catalogue data or contact SKF for the attainable speeds |
| Contact type | Normal contact (two-point contact) |
| Number of rows | 1 |
| Ring type | One-piece inner and outer rings |
| Design | High-speed E |
| Universal matching bearing | Yes, back-to-back (), face-to-face (>>) |
| Matched arrangement | No |
| Matched condition (axial clearance/ preload) | Measuring load, class A |
| Tolerance class | P4A |
| Material, bearing | Hybrid (ceramic balls) |
| Coating | Without |
| Sealing | Without |
| Lubricant | None |
| Special feature | Suitable for direct oil-air lubrication |
| Indicative carbon footprint for new product | 0.36 kg CO_2e |
| Product net weight | 0.098 kg |
| eClass code | 23-05-08-03 |
| UNSPSC code | 31171531 |
| Universal matching bearing(s) | Yes, back-to-back (), face-to-face (>>) |
| Dimensions · Bore diameter · (d) | 40 mm |
| Dimensions · Outside diameter · (D) | 62 mm |
| Dimensions · Width · (B) | 12 mm |
| Dimensions · Shoulder diameter of inner ring (large side face) · (d_1) | 46.5 mm |
| Dimensions · Shoulder diameter of inner ring (small side face) · (d_2) | 44.8 mm |
| Dimensions · Shoulder diameter of outer ring (large side face) · (D_1) | 54.15 mm |
| Dimensions · Width of lubrication groove · (b) | 2 mm |
| Dimensions · Distance from outer ring side face to lubrication groove / lubrication hole · (C_1) | 5.9 mm |
| Dimensions · Distance from outer ring side face to O-ring groove · (C_2) | 1.8 mm |
| Dimensions · Distance from outer ring side face to O-ring groove · (C_3) | 1.8 mm |
| Dimensions · Chamfer dimension · (r_1,2) · min. | 0.6 mm |
| Dimensions · Chamfer dimension · (r_3,4) · min. | 0.3 mm |
| Dimensions · Distance from side face to pressure point · (a) | 14.2 mm |
| Abutment dimensions · Diameter of shaft abutment · (d_a) · min. | 43.2 mm |
| Abutment dimensions · Diameter of shaft abutment · (d_b) · min. | 42 mm |
| Abutment dimensions · Diameter of housing abutment · (D_a) · max. | 58.8 mm |
| Abutment dimensions · Diameter of housing abutment · (D_b) · max. | 60 mm |
| Abutment dimensions · Radius of fillet · (r_a) · max. | 0.6 mm |
| Abutment dimensions · Radius of fillet · (r_b) · max. | 0.3 mm |
| Calculation data · Basic dynamic load rating · (C) | 10.1 kN |
| Calculation data · Basic static load rating · (C_0) | 6 kN |
| Calculation data · Fatigue load limit · (P_u) | 0.186 kN |
| Calculation data · Attainable speeds | Refer to catalogue data or contact SKF for the attainable speeds |
| Calculation data · Attainable speed for grease lubrication | To be calculated: Single bearing () x speed reduction factor (see table below) |
| Calculation data · Attainable speed for oil-air lubrication | To be calculated: Single bearing () x speed reduction factor (see table below) |
| Calculation data · Contact angle · (α) | 18 ° |
| Calculation data · Ball diameter · (D_w) | 6.35 mm |
| Calculation data · Number of rows · (i) | 1 |
| Calculation data · Number of balls (per bearing) · (z) | 19 |
| Calculation data · Reference grease quantity (per bearing) · (G_ref) | 1.4 cm³ |
| Calculation data · Preload and stiffness (back-to-back, face-to-face) · Preload class | A |
| Calculation data · Preload and stiffness (back-to-back, face-to-face) · Preload when unmounted · (G) | 63 N |
| Calculation data · Preload and stiffness (back-to-back, face-to-face) · Axial stiffness | 49 N/µm |
| Calculation data · Correction factors for preload calculation · Correction factor dependent on bearing series and size · (f) | 1.1 |
| Calculation data · Correction factors for preload calculation · Correction factor dependent on contact angle · (f_1) | 1 |
| Calculation data · Correction factors for preload calculation · Correction factor, preload class A · (f_2A) | 1 |
| Calculation data · Correction factors for preload calculation · Correction factor for hybrid bearings · (f_HC) | 1 |
| Calculation data · Factors for equivalent bearing load calculation · Calculation factor for equivalent loads · (f_0) | 8.2 |
| Calculation data · Factors for equivalent bearing load calculation · Additional factors for equivalent loads | Refer to Notes 1 and 2 below |
| Calculation data · Factors for equivalent bearing load calculation · Axial load factor (back-to-back, face-to-face) · (Y_1) | 1.5 |
| Calculation data · Factors for equivalent bearing load calculation · Axial load factor (back-to-back, face-to-face) · (Y_2) | 1.6 |
| Calculation data · Factors for equivalent bearing load calculation · Axial load factor (back-to-back, face-to-face) · (Y_0) | 0.85 |
| Calculation data · Factors for equivalent bearing load calculation · Radial load factor (back-to-back, face-to-face) · (X_1) | 1 |
| Calculation data · Factors for equivalent bearing load calculation · Radial load factor (back-to-back, face-to-face) · (X_2) | 0.7 |
| Calculation data · Factors for equivalent bearing load calculation · Radial load factor (back-to-back, face-to-face) · (X_0) | 1 |
Family specifications and selection conditions
| Product description | These super-precision, high-speed, E design, single row angular contact ball bearings accommodate radial and axial loads acting simultaneously, where the axial load acts in one direction only. They are designed for high-speed operation and, compared to SKF B design high-speed bearings, have a slightly higher speed capability and can accommodate heavier loads. Being universally matchable, they can be used together in arrangements to provide effective load sharing, within a predetermined preload range, without the use of shims or similar devices. They have two lubrication holes in their outer rings, an annular groove, and two annular O-ring grooves in their outer rings. |
|---|---|
| Manufacturer features | Suitable for direct oil-air lubrication • Very high running accuracy • Accommodate very high speeds • Universally matchable |

Manufacturer references
Follow the complete manufacturer documentation for application restrictions, materials, tolerances and installation requirements. Limits may not apply simultaneously. We do not publish inferred stock, pricing or ratings.